Polystyrene was accidentally discovered in 1839 by Eduard Simon, an apothecary in Berlin. From storax, the resin of Liquidambar orientalis, he distilled an oily substance, a monomer which he named styrol. Several days later Simon found that the styrol had thickened, presumably from oxidation, into a jelly he dubbed styrol oxide (“Styroloxyd”). By 1845 English chemist John Blyth and German chemist August Wilhelm von Hofmann showed that the same transformation of styrol took place in the absence of oxygen. They called their substance metastyrol. Analysis later showed that it was chemically identical to Styroloxyd. In 1866 Marcelin Berthelot correctly identified the formation of metastyrol from styrol as a polymerization process. About 80 years went by before it was realized that heating of styrol starts a chain reaction which produces macromolecules, following the thesis of German organic chemist Hermann Staudinger (1881-1965). This eventually led to the substance receiving its present name, polystyrene. The I.G. Farben company began manufacturing polystyrene in Ludwigshafen, Germany, about 1931, hoping it would be a suitable replacement for die cast zinc in many applications. Success was achieved when they developed a reactor vessel that extruded polystyrene through a heated tube and cutter, producing polystyrene in pellet form.
Pure solid polystyrene is a colorless, hard plastic with limited flexibility. It can be cast into molds with fine detail. Polystyrene can be transparent or can be made to take on various colors. It is economical and is used for producing plastic model assembly kits, license plate frames, plastic cutlery, CD “jewel” cases, and many other objects where a fairly rigid, economical plastic is desired.
Polystyrene`s most common use, however, is as expanded polystyrene (EPS). Expanded polystyrene is produced from a mixture of about 90-95% polystyrene and 5-10% gaseous blowing agent, most commonly pentane or carbon dioxide. The solid plastic is expanded into a foam through the use of heat, usually steam. Extruded polystyrene (XPS), which is different from expanded polystyrene (EPS), is commonly known by the trade name Styrofoam. The voids filled with trapped air give it low thermal conductivity. This makes it ideal as a construction material and it is therefore sometimes used in structural insulated panel building systems. It is also used as insulation in building structures, as molded packing material for cushioning fragile equipment inside boxes, as packing “peanuts”, as non-weight-bearing architectural structures (such as pillars), and also in crafts and model building, particularly architectural models. Foamed between two sheets of paper, it makes a more-uniform substitute for corrugated cardboard, tradenamed Fome-Cor. A more unexpected use for the material is as a lightweight fill for embankments in the civil engineering industry.
Expanded polystyrene used to contain CFCs, but other, more environmentally-safe blowing agents are now used. Because it is an aromatic hydrocarbon, it burns with an orange-yellow flame, giving off soot, as opposed to non-aromatic hydrocarbon polymers such as polyethylene, which burn with a light yellow flame (often with a blue tinge) and no soot.
Expanded polystyrene is very easily cut with a hot-wire foam cutter, which is easily made by a heated taut length of wire, usually nichrome because of nichrome`s resistance to oxidation at high temperatures and its suitable electrical conductivity. The hot wire foam cutter works by heating the wire to the point where it can vaporize foam immediately adjacent to it. The foam gets vaporized before actually touching the heated wire, which yields exceptionally smooth cuts.
Polystyrene, shaped and cut with hot wire foam cutters, is used in architecture models, actual signage, amusement parks, movie sets, airplane construction, and much more. Such cutters may cost just a few dollars (for a completely manual cutter) to tens of thousands of dollars for large CNC machines that can be used in high-volume industrial production.
Polystyrene can also be cut with a traditional cutter. In order to do this without ruining the sides of the blade one must first dip the blade in water and cut with the blade at an angle of about 30?. The procedure has to be repeated multiple times for best results.
Polystyrene can also be cut on 3 and 5-axis routers, enabling large-scale prototyping and model-making. Special polystyrene cutters are available that look more like large cylindrical rasps.
Working on the water can be challenging, but expanded polystyrene (EPS) can stand up to cool country lakes or the heartless high seas. Lightweight and impervious to leaking, EPS can be shaped and molded to fit the demand of boaters, surfers and marine construction companies.
Vyacheslav Kulbaka
vyacheslav@royalfoam.us
http://www.youtube.com/watch?v=-sSYKvaaXm0
Related posts:
- Royal Foam manufacturer JACKSONVILLE — A Jacksonville-based foam manufacturer has gotten permission from...
- EPS manufacturer Dear Customer! Since 1992 Royal Foam Inc. (RF) is Jacksonville`s...
- Save Money on Memory Foam Beds There has been much discussion about memory foam beds and...
- Factors to Consider when Buying Memory Foam Mattress If you experience any back pain or sleepless nights, this...
Related posts brought to you by Yet Another Related Posts Plugin.
Feedback